pikavippi ostosraha .

Kia Clarus/Credos

1995-2001 of release

Repair and car operation



KIA Klarus
1.1. Periodicity of maintenance
+ 2. FE DOHC engines and Т8 DOHC
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. АКП G4A–EL
+ 11. АКП 50–40 LE
+ 12. Axes and power shafts
+ 13. Steering
+ 14. Wheels and tires
+ 15. Suspension bracket
- 16. Body
   16.1. Cowl
   16.2. Trunk lid
   16.3. Front bumper
   16.4. Rear bumper
   16.5. Forward door
   16.6. Back door
   16.7. Screen wiper and stekloomyvatel of a windscreen
   16.8. Tank of a stekloomyvatel
   16.9. Windscreen
   16.10. Back glass
   16.11. Dashboard
   16.12. Sitting lobbies
   16.13. Back sitting
   16.14. Mechanism of an inclination of a back
   16.15. Seat belts
   16.16. External rear-view mirror
   16.17. An external rear-view mirror with the electric drive
+ 17. Central air
+ 18. Electric equipment
+ 19. Brake system
+ 20. Electric circuits





16.6. Back door

GENERAL INFORMATION

1–cover of the internal handle;
2–internal furnish of a door;
3–door upholstery;
4–assembly of the internal handle;
5–door filter;
6–directing glasses "And" / "In";
7–glass;
8–window regulator;
9–the operating mechanism of the lock;
10-door lock;
11-a directing groove of glass;
12-door fringing;
13-furnish of a door and central laying;
14-door framework;
15-consolidation;
16-limiter of opening of a door;
17-loops.

Removal

PERFORMANCE ORDER
1. Completely lower door glass.
2. Remove the internal handle, the handle of a window regulator and an armrest.
3. Remove an upholstery of a door and the button of the lock of a door.

Prevention

For cars with electric window regulators and locks of a door disconnect the socket of a plait of wires.


4. Remove the door filter.

Prevention

Remove the door filter carefully that it could be used.


5. Having turned a back part of glass of a door down, turn out bolts of fastening of glass of a door and get door glass up and outside.
6. Turn out bolts of fastening of a window regulator and take a window regulator through a working opening.
7. Remove a window regulator, draft and unscrew nuts of fastening of the external handle.
8. Remove the external handle.
9. Remove the holder of the cylinder of the lock of a door and remove a subgroup of a key of a door.

10. Turn out screws and remove the door lock assembled.
11. Remove a pin of the limiter of opening of a door.
12. Turn out bolts of fastening of loops of a door and remove a door.

Installation

PERFORMANCE ORDER
1. Installation of a door carry out to sequences, return to removal, taking into account the following.
2. At installation of a triangular window leaf grease with soap solution external perimeter of a sealant.
3. After installation of a window regulator adjust it so that door glass easily and smoothly moved up and down.

Prevention

If necessary grease the limiter of opening of a door.

Moments of an inhaling, N • m
Door lock assembled: 4,2–6,18
External handle: 8,8–13
Nut of fastening of a window regulator: 8,8–13
Bolt of fastening of a window regulator: 7,8–11
Doggie of the lock of a door: 18–26
Bolt of fastening of a loop of a door: 18–29



Adjustment

PERFORMANCE ORDER
1. Check, that the door was easily closed, and was not люфта. In case of need weaken screws of a doggie of fastening and adjust the provision of a door, moving a doggie of the lock of a door on a vertical or across.
2. Check a back gap between a door and a body. In case of need adjust a door, moving a doggie of the lock of a door across.

Inhaling moment: 18–26 N • m

Door loops

PERFORMANCE ORDER
1. Open a door and if in loops is available люфт, tighten bolts of fastening of a loop of a door (are shown by shooters).
2. To adjust a gap between a door and a body, weaken bolts of fastening of a loop of a door and carry out adjustment.

Inhaling moment: 17,64–29,4 N • m