Kia Clarus/Credos

1995-2001 of release

Repair and car operation

KIA Klarus
1.1. Periodicity of maintenance
+ 2. FE DOHC engines and Т8 DOHC
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
- 7. Ignition system
   7.1. Specifications
   7.2. Iskroobrazovaniye check
   7.3. Spark plugs
   7.4. Check of spark plugs
   7.5. High-voltage wires
   7.6. Ignition coil
   7.7. Ignition distributor
   7.8. Search and elimination of malfunctions
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. АКП G4A–EL
+ 11. АКП 50–40 LE
+ 12. Axes and power shafts
+ 13. Steering
+ 14. Wheels and tires
+ 15. Suspension bracket
+ 16. Body
+ 17. Central air
+ 18. Electric equipment
+ 19. Brake system
+ 20. Electric circuits

7.2. Iskroobrazovaniye check

PERFORMANCE ORDER

1. Disconnect a wire from the negative plug of the storage battery. For a tip disconnect high-voltage wires from spark plugs.
Prevention At a detachment of high-voltage wires from spark plugs pull for a wire tip, instead of for a wire as it can be damaged.
2. The compressed air clear candles that will exclude dirt hit in engine cylinders after a vyvinchivaniye of spark plugs. Turn out a candle, using a candle key. For an exception of damage of a candle establish a candle key strictly along a candle axis.
3. Connect a spark plug to a high-voltage wire.
	4. Holding a spark plug special пассатижами with the isolated handles, keep a spark plug at arm's length 5–10 mm from "weight".
Prevention Do not concern a car body during performance of the following operations.
5. The assistant should turn a cranked shaft of the engine a starter, thus between electrodes of a candle the steady strong iskroobrazovaniye should be observed.
6. In the absence of a spark of ignition or if an ignition spark weak, execute the following checks.

FE DOHC engine

Step	Check		Action
1	Check existence of good connection of the following knots: – ignition coils; – ignition distributor.	Yes	Pass to the following step
		No	Eliminate malfunction or make replacement
2	Check resistance of high-voltage wires Resistance: 16 kiloohms/m	Yes	Pass to the following step
		No	Replace wires
3	Check existence of an electric charge in the ignition coil 1. Turn on the ignition switch 2. Check existence of an electric charge in the ignition coil (a conclusion "+")	Yes	Pass to the following step
		No	Check wires between the ignition switch, the coil of ignition and the control unit
4	Check resistance of the coil of ignition Resistance of primary winding: 0,81–0,99 Ohm (at 20°С)	Yes	Pass to the following step
		No	Replace the ignition coil
5	Check serviceability of a cover of the distributor of ignition (a gap between a rotor and a distributor cover)	Yes	Pass to the following step
		No	Replace a cover of the distributor of ignition
6	Check serviceability of the RSM control unit	Yes	–
		No	Replace the RSM control unit

DOHC T8 engine

Step	Check		Action
1	Check quality of connection of the coil of ignition	Yes	Pass to the following step
		No	Eliminate malfunction
2	Disconnect the socket of ignition and check electric connection at the included ignition	Yes	Pass to the following step
		No	Check wires between the control unit and the ignition coil
3	Check resistance of the coil of ignition Resistance Primary winding: 0,45–0,55 Ohm (at 20°С) the Secondary winding: 13–15 kiloohms (at 20°С)	Yes	Pass to the following step
		No	Replace the ignition coil
4	Check serviceability of the RSM control unit	Yes	–
		No	Replace the RSM control unit