Kia Clarus/Credos

1995-2001 of release

Repair and car operation

KIA Klarus
1.1. Periodicity of maintenance
+ 2. FE DOHC engines and Т8 DOHC
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. АКП G4A–EL
+ 11. АКП 50–40 LE
- 12. Axes and power shafts
   12.1. Specifications
   12.2. Rotary fist and nave of a forward wheel
   12.3. Repair of a rotary fist
   12.4. Back suspension bracket
   12.5. Back axis
   12.6. Power shafts
   12.7. Right driving and intermediate shaft
   12.8. Dismantling and assembly of an intermediate shaft
   12.9. Left power shaft
   12.10. A power shaft with CV JOINTS of tripoidny type
   12.11. Search and elimination of malfunctions
+ 13. Steering
+ 14. Wheels and tires
+ 15. Suspension bracket
+ 16. Body
+ 17. Central air
+ 18. Electric equipment
+ 19. Brake system
+ 20. Electric circuits

12.2. Rotary fist and nave of a forward wheel

GENERAL INFORMATION

1–nut of fastening of a wheel;
2–wheel;
3–a nut with a fillet;
4–support of a forward brake;
5–brake disk;
6–the sensor of frequency of rotation of a wheel (the cars equipped with anti-blocking system of brakes – ABS);

7–tip of steering draft;
8–stabilizer earring;
9–spherical hinge of the bottom lever;
10-rotary fist.

Check люфта wheel bearing

PERFORMANCE ORDER

1. Lift the car and fix on support. Turn out four nuts of fastening of a wheel and remove a wheel.
2. Remove a support and a brake disk.
	3. Establish a measuring tip of the indicator of hour type on an end face of a nave of a forward wheel and, moving a nave along an axis, measure люфт the bearing. If necessary replace the wheel bearing. Maximum permissible люфт: 0,1 mm

Removal

PERFORMANCE ORDER

1. Lift the car and fix on support.
2. Turn out four nuts of fastening of a wheel.
3. Remove a wheel.
4. Unbend a fillet and unscrew a nut of fastening of a power shaft to a nave and turn out two bolts of fastening of a brake disk.
5. Remove a support and a brake disk.
Prevention Do not damage a dustproof cover.
	6. Take шплинт and unscrew a nut of fastening of a pin of the spherical hinge of a tip of steering bent for to a rotary fist. A stripper OK130 283 021 squeeze out a pin of the spherical hinge from a rotary fist.
7. Disconnect an earring of the stabilizer of cross-section stability from the bottom cross-section lever of a forward suspension bracket.
8. Turn out a coupling bolt, mount wring out the bottom lever down and separate a hinge pin from a rotary fist.
9. Note situation and turn out bolts of fastening of the lower part of a rack of a forward suspension bracket to a rotary fist. Remove a rotary fist and a nave of a forward wheel.
10. Check a condition of all details and, if necessary, restore or replace the damaged details.

Installation

PERFORMANCE ORDER

1. Establish a rotary fist and a wheel nave, fix bolts to the lower part of a rack of a forward suspension bracket.
2. Establish a pin of the spherical hinge of the bottom lever in a rotary fist and fix a coupling bolt and a nut. Inhaling moment: 92–116 N • m
3. Establish a brake disk on a nave of a wheel and fix two bolts.
4. Establish a support of a forward brake on a rotary fist and fix two bolts. Inhaling moment: 78–102 N • m
Prevention Do not damage a dustproof cover.
5. Establish a pin of the spherical hinge of a tip of steering draft in a rotary fist.
6. Screw nuts and shplinty fix them from an otvorachivaniye.
	7. Screw a new nut with a fillet and hammer a nut fillet into a groove of a power shaft. Inhaling moment: 235,5–318,8 N • m
8. Establish a wheel.
9. Tighten nuts of fastening of a wheel.
10. Freely screw nuts of fastening of an earring of the stabilizer, lower the car and on the car standing on wheels, tighten nuts.
11. Check corners of installation of forward wheels.