Kia Clarus/Credos

1995-2001 of release

Repair and car operation



KIA Klarus
1.1. Periodicity of maintenance
+ 2. FE DOHC engines and Т8 DOHC
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. АКП G4A–EL
+ 11. АКП 50–40 LE
+ 12. Axes and power shafts
+ 13. Steering
+ 14. Wheels and tires
+ 15. Suspension bracket
+ 16. Body
+ 17. Central air
- 18. Electric equipment
   18.1. Specifications
   18.2. Devices for check of elements of the electric equipment and electric chains
   18.3. Electric sockets
   18.4. Wires
   18.5. Fuse replacement
   18.6. Main and fuses
   18.7. Box of the main safety locks
   18.8. Fuse
   18.9. Storage battery
   18.10. Generator
   18.11. Check of a sound signal
   18.12. Check of a heater of back glass
   18.13. Switch of a heater of back glass
   18.14. Relay of a heater of back glass
   18.15. Combination of devices
   18.16. Safety cushion (SRS)
   18.17. System of blocking of the car
+ 19. Brake system
+ 20. Electric circuits





18.10. Generator

GENERAL INFORMATION

1–the screw with a turnkey head;
2–pulley;
3–forward cover;
4–rotor;
5–back cover;
6–stator;
7–rectifier;
8–knot of a shchetkoderzhatel;
9–bearing.


The generator develops a target current force 80 And and has the built-in electronic regulator of tension. It is established on a forward part of the engine and is put in action by a belt with four edges which puts in action and the fan with the thermorelay.

On the generator there are three plugs by means of which it is connected to electric system of the car. The plug B (the storage battery) settles down on the back party of the generator, and plugs (L) (lamp) and (S) (sensors) settle down on a lateral surface.

Plugs L and S have designations on the generator case.

Removal and installation

PERFORMANCE ORDER
1. Disconnect a wire from the negative plug of the storage battery.
2. Unscrew a nut from the plug B.
3. Remove a wire from the plug B.
4. Disconnect the electric socket from the generator.
5. Turn out an adjusting bolt.
6. Turn out a bolt of fastening of the generator.
7. Remove a driving belt from a generator pulley.
8. Remove the generator from the car.
9. Installation is carried out to sequences, return to removal.

10. Adjust a belt tension with V-shaped crests.

Deflection of a belt of a drive of the generator of the FE DOHC engine
The new: 6,0–8,0 mm
Being in the use: 7,0–9,0 mm
Deflection of a belt of a drive of the generator of the DOHC T8 engine
The new: 8,0–9,0 mm
Being in the use: 9,0–10,1 mm

Inhaling moment
Bolt And: 19–26 Nanometers
Bolt In: 38–53 Nanometers


Prevention

Be convinced that wires of the storage battery are correctly connected.

Do not use high-voltage devices, such as мегомметра for check of resistance.

Remember that tension of the storage battery always moves to the plug B of the generator of an alternating current.

Do not connect to "weight" contact of L at operation of the engine.

Do not start up the engine while contacts of L and S are disconnected from the generator.