KIA Klarus
1.1. Periodicity of maintenance
+ 2. FE DOHC engines and Т8 DOHC
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. АКП G4A–EL
+ 11. АКП 50–40 LE
+ 12. Axes and power shafts
+ 13. Steering
+ 14. Wheels and tires
+ 15. Suspension bracket
+ 16. Body
+ 17. Central air
- 18. Electric equipment
18.1. Specifications
18.2. Devices for check of elements of the electric equipment and electric chains
18.3. Electric sockets
18.4. Wires
18.5. Fuse replacement
18.6. Main and fuses
18.7. Box of the main safety locks
18.8. Fuse
18.9. Storage battery
18.10. Generator
18.11. Check of a sound signal
18.12. Check of a heater of back glass
18.13. Switch of a heater of back glass
18.14. Relay of a heater of back glass
18.15. Combination of devices
18.16. Safety cushion (SRS)
18.17. System of blocking of the car
+ 19. Brake system
+ 20. Electric circuits
|
1–speedometer;
2–way counter;
3–the way counter for one trip;
4–index of level of fuel;
5–the index of temperature of cooling liquid; |
6–tachometer;
7–emergency turn alarm system / index;
8–alarm and display lamps;
9–the button of dumping of the counter of a way for one trip. |
The speedometer does not work or its indications are incorrect
Step 1
| PERFORMANCE ORDER |
| Check connection of the measuring block and the socket of the sensor of speed. |
|
Step 2: check the sensor of speed
| PERFORMANCE ORDER |
| 1. In a motor compartment disconnect the socket from the sensor of speed established on a conducted gear wheel of a transmission. |
| 2. Remove the sensor of speed. |
| 3. Connect a conclusion of 1 sensor of speed to positive (+) to a battery conclusion, and a conclusion 2 sensors – to negative (–) to a battery conclusion. |
| 4. Connect a conclusion 2 sensors of speed to the negative (–) to a tester conclusion, and a conclusion 3 – to positive (+) to a conclusion. |
| 5. Turn a shaft of the sensor of speed. |
|
6. Check a range of change of tension between conclusions 3 and 2.
Range of change of tension: 0–12 In |
Prevention
Tension should change 4 times for a turn of a shaft of the sensor of speed. If it not so, replace the sensor of speed.
|
|
Step 3: check a speedometer
| PERFORMANCE ORDER |
| 1. Disconnect the measuring block. |
|
2. Check conductivity between conclusions "IN" (orange-dark blue) and "AS" (black) a speedometer, at the same time rotating a sensor shaft. If for one turn of a shaft of the sensor of speed 4 impulses are not formed, replace a measuring instrument of speed. |
|
The tachometer does not work
| PERFORMANCE ORDER |
| 1. Remove a combination of devices. |
|
2. Connect a tachometer to "Af" conclusions (white-dark blue) and "As" (black) the socket of a combination of devices. |
| 3. Start up the engine. |
4. Check, whether shows a tachometer frequency of rotation of a shaft of the engine.
|
Result
|
Action
|
|
Yes
| Replace a tachometer |
|
No
| Repair conducting (on a site a combination of devices – a tachometer) |
|
|
The index of temperature of cooling liquid does not work
| PERFORMANCE ORDER |
| 1. Disconnect the socket from the sensor of cooling liquid. |
|
2. Connect a red wire of the special tool to the socket, and a black wire connect to the case. |
| 3. Establish value of resistance of the special tool, equal specified for the sensor of temperature of cooling liquid. |
4. Include ignition and check correctness of indications.
|
Result
|
Action
|
|
Yes
| Replace the sensor |
|
No
| See a step 7. |
|
Prevention
For the correct determination of malfunction continue the check described above within not less than 2 minutes. The admissible error is equal to the doubled thickness of an arrow of the index.
|
|
|
| 5. Remove a combination of devices. |
| 6. Submit tension with positive (+) battery poles on the conclusion "Вn" of the socket, and a conclusion of "AS" connect to the case. |
|
7. Connect a red wire of the special tool to "Bd" conclusion, and a black wire – to a negative pole of the battery. |
| 8. Establish resistance of the special tool. |
| 9. Check correctness of indications of the index. |
|
|
|
Check of the sensor of temperature of cooling liquid
| PERFORMANCE ORDER |
| 1. Remove the sensor. |
|
2. Establish the sensor in a vessel with water. |
| 3. Measure resistance, gradually heating up water. |
| 4. If resistance differs from specified, replace the sensor. Resistance: 190–260 Ohm at 50°С
|
|
The index of level of fuel does not work
| PERFORMANCE ORDER |
| 1. Disconnect the socket from the sensor of the index of level of fuel. |
|
2. Connect a red wire of the special tool to a conclusion of a flavovirent wire, and a black wire connect to "weight". |
| 3. Establish value of resistance of the special tool. |
4. Include ignition and check correctness of indications.
|
Result
|
Action
|
|
Yes
| Replace the sensor |
|
No
| See a step 7. |
|
Prevention
For the correct determination of malfunction continue the check described above within not less than 2 minutes. The admissible error is equal to the doubled thickness of an arrow of the index.
|
|
|
| 5. Remove a combination of devices. |
|
6. Submit tension 12 In on the conclusion "Вn" of the socket, and a conclusion of "As" connect to the case. |
| 7. Connect a red wire of the special tool to a conclusion of "Vr", and a black wire – to a negative pole of the battery. |
| 8. Establish resistance of the special tool. |
9. Check correctness of indications of the index.
|
Result
|
Action
|
|
Correctly
| Replace wiring (on a site a combination of devices – the sensor of the index of level of fuel) |
|
Incorrectly
| Index of level of fuel |
|
Prevention
For the correct determination of malfunction continue the check described above within not less than 2 minutes. The admissible error is equal to the doubled thickness of an arrow of the index.
|
|
Check
| PERFORMANCE ORDER |
| 1. Remove fuel level sensor knot. |
| 2. Disconnect the socket from knot of the sensor of level. |
|
3. Measure resistance, slowly moving a float from "F" point to the point "Е". |
|
Control lamp of brake system
| PERFORMANCE ORDER |
| 1. Disconnect the socket from the sensor of level of brake liquid. |
| 2. Connect conclusions of red-white and black wires a connecting wire. |
|
3. Turn on the engine and be convinced that the control lamp of brake system lights up. |
Prevention
Before check be convinced that the parking brake is switched completely off.
|
| 4. If the lamp did not light up, check a safety lock, a lamp and conducting. |
|
Sensor of level of brake liquid
| PERFORMANCE ORDER |
| 1. Connect an ohmmeter to the socket of the sensor of level of brake liquid. |
| 2. Check conductivity according to amount of brake liquid. |
|
3. The sensor is serviceable, if conductivity is, when level of liquid is lower than "MIN" mark, and is absent, when level of liquid is higher than a mark "MOVE". |
| 4. If the sensor did not pass this check, replace it. |
|
Control lamp of level of fuel
| PERFORMANCE ORDER |
| 1. Disconnect the socket from the fuel level sensor. |
| 2. Connect a conclusion of a red-white wire on the socket to the case. |
|
3. Turn on the engine and be convinced that the control lamp burns. |
| 4. If the lamp did not light up, check a safety lock, a lamp and conducting. |
|
Control lamp of a charging
| PERFORMANCE ORDER |
| 1. Turn on the engine and connect a white-black wire to the case. |
| 2. Be convinced that the control lamp burns. |
| 3. If the lamp did not light up, check an alarm lamp, conducting and the generator. |
|
4. If necessary repair or replace. |
| |
|
Control lamp of pressure of oil of the engine
| PERFORMANCE ORDER |
| 1. Disconnect the socket from the sensor of pressure of oil of the engine. |
| 2. Turn on the engine and connect a conclusion of a yellow-red wire to the case. |
|
3. Be convinced that the control lamp "OIL" (OIL) lit up. If the lamp did not light up, check a lamp, the sensor of pressure of oil and conducting. |
| 4. If necessary repair or replace. |
|
Control lamp of seat belts
| PERFORMANCE ORDER |
| 1. Disconnect the socket from the switch on the lock of seat belts. |
| 2. Connect conclusions of green-orange and black wires a connecting wire. |
|
3. Include ignition and be convinced that the control lamp and a sound signal join approximately on 6 villages. |
| 4. If the lamp and a sound signal did not join, check a lamp, the switch on the lock, conducting and the control unit. If necessary repair or replace. |
|
|
|