Kia Clarus/Credos

1995-2001 of release

Repair and car operation



KIA Klarus
1.1. Periodicity of maintenance
+ 2. FE DOHC engines and Т8 DOHC
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. АКП G4A–EL
+ 11. АКП 50–40 LE
+ 12. Axes and power shafts
- 13. Steering
   13.1. Specifications
   13.2. Check of a free wheeling of a steering wheel
   13.3. Check of effort of turn of a steering wheel
   13.4. Belt of a drive of the pump of the amplifier of a steering
   13.5. Check of pressure of liquid in hydraulic system
   13.6. Replacement of a protective cover of steering draft
   13.7. Steering shaft
   13.8. Steering transfer
   13.9. Pump of the amplifier of a steering (FE DOHC)
   13.10. Dismantling and assembly of the pump of the amplifier of a steering (FE DOHC)
   13.11. Search and elimination of malfunctions
+ 14. Wheels and tires
+ 15. Suspension bracket
+ 16. Body
+ 17. Central air
+ 18. Electric equipment
+ 19. Brake system
+ 20. Electric circuits





13.6. Replacement of a protective cover of steering draft

GENERAL INFORMATION

Protective cover of steering draft

1–шплинт;
2–nut;
3–tip of steering draft;
4–protective cover of the hinge of a tip of steering draft;
5–lock nut;
6–collar;
7–wire.

Removal

PERFORMANCE ORDER
1. Lift a forward part of the car and fix on support. Remove a wheel.
2. Remove a plastic guard of protection of an arch of a wheel.
3. Turn a wheel to the left against the stop.
4. Take шплинт and unscrew a nut of fastening of a finger of the spherical hinge of a tip of steering bent for to a rotary fist. Turn on a nut until it will not reach the finger end.
5. A stripper OK130 283 021 squeeze out a finger of the spherical hinge of a tip of steering draft from a rotary fist.

Prevention

For an exception of damage of a carving of a pin screw on a carving a temporary nut. Do not tighten a nut strongly not to damage a carving.


6. Note the provision of a tip of steering draft, weaken a lock-nut and unscrew a tip of steering draft from steering draft.
7. Fix a tip of steering draft in a vice.
8. Press a chisel to a cover, holding it at an angle, shown in drawing.

9. Gradually, being careful and moving a chisel round the hinge, bring down a protective cover.


Prevention

Do not damage a place of a prileganiye of a dustproof cover to steering draft.


10. Cut a wire and weaken a collar of fastening of a protective cover of steering transfer.
11. Turn out a lock-nut from steering draft.
12. Shifting on steering draft, remove a protective cover of steering transfer.
13. Remove collars from a protective cover.

Installation

PERFORMANCE ORDER
1. Put a small amount of greasing in a protective cover of a tip of steering draft.
2. A press and an opravka establish a protective cover on a tip of steering draft.
3. Fill a new protective cover of steering transfer with lubricant.
4. Apply a thin film greasings on interfaced surfaces of a protective cover.
5. Pulling on steering draft, establish a protective cover of steering transfer. Fix the big party of a cover a wire, having wrapped up it on two turns, and twirl the ends of a wire 4-4,5 times.
6. Fix a cover from the smaller party a collar.
7. Screw a lock-nut of steering draft and combine the labels put before a reversing of a nut.
8. Screw a tip of steering draft and combine the labels put before a reversing of a tip.
9. Tighten a lock-nut of a tip of steering draft.

10. Establish a finger of the spherical hinge of a tip of steering draft in a rotary fist.

11. Screw a nut of fastening of a finger and tighten it the demanded moment.
12. Establish шплинт.
13. Establish a wheel.
14. Lower the car.
15. After installation check adjustment of corners of installation of wheels.