Kia Clarus/Credos

1995-2001 of release

Repair and car operation



KIA Klarus
1.1. Periodicity of maintenance
+ 2. FE DOHC engines and Т8 DOHC
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. АКП G4A–EL
+ 11. АКП 50–40 LE
+ 12. Axes and power shafts
+ 13. Steering
+ 14. Wheels and tires
- 15. Suspension bracket
   15.1. Specifications
   15.2. Adjustment of corners of installation of forward wheels
   15.3. Adjustment of corners of installation of back wheels
   15.4. A forward amortization rack with a spring
   15.5. Repair of an amortization rack of a forward suspension bracket
   15.6. Bottom lever of a forward suspension bracket
   15.7. Forward stabilizer of cross-section stability
   15.8. Draft of the forward stabilizer of cross-section stability
   15.9. Traverse
   15.10. Back amortization rack
   15.11. Repair of a back amortization rack
   15.12. Back stabilizer of cross-section stability
   15.13. Draft of the back stabilizer of cross-section stability
   15.14. Cross-section and longitudinal drafts
   15.15. Back cross-piece
   15.16. Search and elimination of malfunctions
+ 16. Body
+ 17. Central air
+ 18. Electric equipment
+ 19. Brake system
+ 20. Electric circuits





15.2. Adjustment of corners of installation of forward wheels

Check is preliminary

PERFORMANCE ORDER
1. Check pressure in tires and if necessary finish it to the recommended.
2. Check люфт the bearing of a forward wheel and if necessary replace the bearing.
3. Check wheel and tire palpation.
4. Check the spherical hinge and a steering drive on existence of the increased wear.
5. The car should stand on a horizontal surface and not have neither cargo, nor passengers.
6. For check of operation of the shock-absorber shake the car in the vertical direction.

Check of the general positive convergence

PERFORMANCE ORDER
1. Lift a forward part of the car so that forward wheels appeared over the earth.
2. Turning a wheel a hand, chalk note the line on the center of tires.
3. Establish forward wheels in the direction of rectilinear movement and establish the car on a horizontal surface.
4. Measure distances And and Century.

Positive convergence: 3±3 mm


Adjustment

PERFORMANCE ORDER
1. Weaken lock nuts of the left and right connecting drafts and turn connecting drafts on the same size.

Prevention

One turn of connecting draft (both parties) changes a positive convergence approximately for 6 mm.


2. Tighten lock nuts of connecting drafts.

Inhaling moment: 70–100 N • m

Check of the maximum angle of rotation

PERFORMANCE ORDER
Establish both lobbies of a wheel in a template of radius of turn.

Inside: 31,19 °
Outer side: 36,17 °


Adjustment of the maximum angle of rotation

PERFORMANCE ORDER
1. Weaken lock nuts of the left and right connecting drafts and turn connecting drafts on the same size.

The maximum difference between the left and right drafts: 3 mm
2. Tighten lock nuts of connecting drafts.

Inhaling moment: 70–100 N • m
3. After adjustment of an angle of rotation check and adjust a positive convergence.

Check of disorder and corner of a longitudinal inclination шкворня

PERFORMANCE ORDER
1. Establish a forward wheel on the device for measurement of radius of turn and unscrew lock nuts of a nave.
2. Fix on a nave the device for measurement of a disorder / corner of a longitudinal inclination шкворня.

3. Measure a disorder / corner of a longitudinal inclination шкворня.

Disorder: 0 ° 42 '±45'
Corner of a longitudinal inclination шкворня: 2 ° З0 '±45'

4. Remove the device for measurement of a disorder / corner of a longitudinal inclination шкворня.
5. Tighten new lock nuts of a nave and зачеканьте them.

Inhaling moment: 235–319 N • m

Adjustment of disorder and corner of a longitudinal inclination шкворня

PERFORMANCE ORDER
1. Lift a forward part of the car and establish it on a reliable support.
2. Turn out nuts of the fixing block.
3. Press the assembly block and turn it in the necessary direction.
4. Again screw nuts of fastening of the assembly block and tighten them the demanded moment.

Inhaling moment: 46–63 N • m