The device, service and Kia Clarus/Credos repair - 15.3. Adjustment of corners of installation of back wheels//KIA Klarus / Kredos of 1995-2001 - doska-parketnaja.ru

Kia Clarus/Credos

1995-2001 of release

Repair and car operation



KIA Klarus
1.1. Periodicity of maintenance
+ 2. FE DOHC engines and Т8 DOHC
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. АКП G4A–EL
+ 11. АКП 50–40 LE
+ 12. Axes and power shafts
+ 13. Steering
+ 14. Wheels and tires
- 15. Suspension bracket
   15.1. Specifications
   15.2. Adjustment of corners of installation of forward wheels
   15.3. Adjustment of corners of installation of back wheels
   15.4. A forward amortization rack with a spring
   15.5. Repair of an amortization rack of a forward suspension bracket
   15.6. Bottom lever of a forward suspension bracket
   15.7. Forward stabilizer of cross-section stability
   15.8. Draft of the forward stabilizer of cross-section stability
   15.9. Traverse
   15.10. Back amortization rack
   15.11. Repair of a back amortization rack
   15.12. Back stabilizer of cross-section stability
   15.13. Draft of the back stabilizer of cross-section stability
   15.14. Cross-section and longitudinal drafts
   15.15. Back cross-piece
   15.16. Search and elimination of malfunctions
+ 16. Body
+ 17. Central air
+ 18. Electric equipment
+ 19. Brake system
+ 20. Electric circuits





15.3. Adjustment of corners of installation of back wheels

Check of the general positive convergence

PERFORMANCE ORDER
1. Lift a back part of the car so that back wheels appeared over the earth.
2. Turning a wheel a hand, chalk note the line on the center of tires.
3. Establish the car on a horizontal surface.
4. Measure distances And and Century.

Positive convergence: 3±3 mm

Adjustment of a positive convergence

Prevention

At installation of a corner of axial loading according to norm for positive a convergence of back wheels value of the corner measured by means of the device for adjustment of 4 wheels, should be in limits of the established values. At default of this requirement check the sizes of a body.

Corner of axial loading: 0 °±0,10


PERFORMANCE ORDER
1. Uncover.
2. Weaken a kulachkovy nut of cross-section draft.
3. Adjust a positive convergence, turning an adjusting bolt with a kulachkovy head as follows:

Left wheel
Right wheel
Positive convergence counter-clockwise clockwise
Negative convergence clockwise counter-clockwise

Prevention

One turn of an adjusting bolt with a kulachkovy head changes a positive convergence approximately for 3,2 mm.


4. Tighten kulachkovy nuts.

Inhaling moment: 78–117 N • m

5. Establish a cover.

Disorder check

PERFORMANCE ORDER
1. Remove wheels.
2. Uncover and turn on nuts of fastening of a nave.
3. Establish the device for measurement of a disorder / corner of a longitudinal inclination шкворня.
4. Measure disorder.

Razval:-0 ° 21 '±45'


Prevention

Adjustment of disorder is impossible.


5. Remove the device for measurement of a disorder / corner of a longitudinal inclination шкворня.
6. Tighten new nuts of fastening of a nave of a wheel and зачеканьте them.

Inhaling moment: 235–319 N • m

7. Establish wheels.

Inhaling moment: 88–117 N • m