Kia Clarus/Credos

1995-2001 of release

Repair and car operation



KIA Klarus
1.1. Periodicity of maintenance
+ 2. FE DOHC engines and Т8 DOHC
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. АКП G4A–EL
+ 11. АКП 50–40 LE
+ 12. Axes and power shafts
+ 13. Steering
+ 14. Wheels and tires
+ 15. Suspension bracket
- 16. Body
   16.1. Cowl
   16.2. Trunk lid
   16.3. Front bumper
   16.4. Rear bumper
   16.5. Forward door
   16.6. Back door
   16.7. Screen wiper and stekloomyvatel of a windscreen
   16.8. Tank of a stekloomyvatel
   16.9. Windscreen
   16.10. Back glass
   16.11. Dashboard
   16.12. Sitting lobbies
   16.13. Back sitting
   16.14. Mechanism of an inclination of a back
   16.15. Seat belts
   16.16. External rear-view mirror
   16.17. An external rear-view mirror with the electric drive
+ 17. Central air
+ 18. Electric equipment
+ 19. Brake system
+ 20. Electric circuits






16.9. Windscreen

GENERAL INFORMATION

1–windscreen;
2–forward slip;
3–windscreen fringing.

Tool kit 0305 870 And for removal and glass installation

1–tool box;
2–a syringe for a sealant;
3–molding stripper;
4–royalny wire;
5–rags;
6–brush;
7–pricker;
8–knife;
9–whetstones.

Removal

Prevention

For removal and installation of glass use a special tool kit. 49 0305 870 And.


PERFORMANCE ORDER
1. Disconnect a wire from the negative plug of the storage battery.
2. Remove an internal rear-view mirror, an antisolar peak, the ceiling console, facing of the top forward doorframe and a forward rack and a windscreen fringing.
3. Remove a screen wiper.
4. Remove glass, having separated glass from a sealant by means of the standard electric or manual demountable tool, or use the following procedure.

By means of a pricker make an opening in a sealant. Pass through this opening the end of a piece of a royalny wire (in the length about 40 cm and attach to both ends whetstones.
5. Two persons should take these whetstones, one from within, and another outside of the car, and then to cut a sealant round glass.
6. Remove glass from a body.
7. Remove a fringing from glass

Prevention

Enclose a plastic plate under a royalny wire where it concerns the dashboard, and then move a plate along a cut site.

Cut on border between glass and a sealant.

In case of very strong warming up the royalny wire can burst, therefore periodically let's to it cool down and do not work too long at one place.

If glass is not subject to a reuse, removal can be made quicker if instead of royalny wire to use the tool similar shown in drawing.


 

Installation

PERFORMANCE ORDER
1. By means of a knife accurately level a sealant on a body. Leave a layer in thickness about 1-2 mm.

Prevention

In case of a vykrashivaniye of an old sealant put on these places a new sealant.


2. Carefully clear and remove all konsistentny greasing in a zone in width of 5 cm on perimeter of glass and the glue which has remained on a body.
3. Put the first layer of a first coat on glass perimeter at distance of 15 mm from edge.
4. Paste a slip on glass perimeter at distance of 13 mm from edge.

Prevention

Strongly paste a slip and let's to it dry out.


5. Establish a fringing on glass.
6. By means of a brush put a first coat on glass and body perimeter and let's to it dry out within 20-30 minutes.

Prevention

Do not allow contact of the grounded surfaces to dirt, water, oil etc. and do not touch them.


7. Establish struts and clips in the provisions shown in drawing.
8. When the first coat will dry, put by means of a syringe for a sealant the roller of a repair sealant in thickness of 11 mm at distance of 8 mm from a glass edge.

Prevention

Cut off a nozzle of the boss of a repair sealant, as is shown in drawing.

If necessary smooth a layer of a repair sealant to correct any roughnesses.



Prevention

Combine labels on glass with V-shaped grooves on struts.

Time of hardening of a repair sealant
At temperature 20°С
Time of hardening of a surface: 1 hour
Time demanded prior to the beginning of operation of the car: 4 hours
At temperature 35°С
Time of hardening of a surface: 10 minutes.
Time demanded prior to the beginning of operation of the car: 2 hours


9. If necessary remove surpluses or add a repair sealant.
10. Check on lack of a leak of water. At leak detection carefully remove water and add a repair sealant (В001. 77 739).
11. After check on lack of a leak of water establish rack furnish, the panel of a forward wall, a lattice of a forward wall, a screen wiper etc.
12. Establish a rear-view mirror, an antisolar peak, the ceiling console, facing of the top forward doorframe and a forward rack and a windscreen fringing.