KIA Klarus
1.1. Periodicity of maintenance
+ 2. FE DOHC engines and Т8 DOHC
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
+ 10. АКП G4A–EL
+ 11. АКП 50–40 LE
+ 12. Axes and power shafts
+ 13. Steering
+ 14. Wheels and tires
+ 15. Suspension bracket
+ 16. Body
+ 17. Central air
+ 18. Electric equipment
- 19. Brake system
19.1. Specifications
19.2. Pumping of hydraulic system of a drive of brakes
19.3. Check of brake tubes and hoses
19.4. Replacement of brake hoses
19.5. Height of installation of a pedal of a brake
19.6. Free wheeling of a pedal of a brake
19.7. Distance of a pedal of a brake from a floor
19.8. Brake pedal
19.9. Check of the switch of a stoplight
19.10. Main brake cylinder
19.11. Check of the vacuum amplifier of brakes
19.12. Forward disk brake
19.13. Back disk brake
19.14. Pressure regulator
19.15. Parking brake
19.16. Anti-blocking system of brakes (ABS)
19.17. List of codes of malfunctions of brake system
19.18. Precautions at carrying out repair
19.19. Pumping of hydraulic system of a drive of brakes
19.20. Hydraulic control unit (HCV)
19.21. ABS control unit
19.22. Sensors of frequency of rotation of a wheel
19.23. Rotor of the forward sensor
19.24. Main survey
19.25. Check of functionality
19.26. Search and elimination of malfunctions
+ 20. Electric circuits
|
Main brake cylinder and vacuum amplifier of brakes
1–socket of the sensor of level of brake liquid;
2–brake pipeline;
3–nut; |
4–tank;
5–sealing ring;
6–vacuum amplifier of brakes. |
Removal and installation
Prevention
Brake liquid dissolves paint, plastic and isolation of wires therefore at casual hit of liquid on a paint and varnish covering of the car or its components wash out them a large amount of water.
| PERFORMANCE ORDER |
| 1. Disconnect a wire from the negative plug of the storage battery. |
| 2. Disconnect the socket from the sensor of level of brake liquid. |
| 3. Disconnect brake tubes from the main brake cylinder and close them plastic jams for an exception of hit of dirt in them. |
| 4. Turn out two nuts of fastening of the main brake cylinder. |
| 5. Remove the main brake cylinder. |
|
Check
| PERFORMANCE ORDER |
|
1. By means of the special tool measure a gap between a pusher of the vacuum amplifier of brakes and the piston of the main cylinder.
Gap: 0 mm |
| 2. If the gap differs from nominal rate, adjust it pusher rotation. |
Prevention
| Depression, mm Hg. | Gap between a pusher and the piston, mm |
| 0 | 0,4–0,6 |
| 500 | 0,1–0,4 |
|
|
|
| 3. By means of an ohmmeter check conductivity the sensor of level of brake liquid when level of liquid is below MIN mark. |
|
Installation
| PERFORMANCE ORDER |
| 1. At installation of the new main brake cylinder adjust the provision of a pusher of the vacuum amplifier of brakes. |
| 2. Establish the main brake cylinder on the vacuum amplifier of brakes and screw two nuts. |
| 3. Tighten two nuts of fastening of the main brake cylinder. Inhaling moment: 9,8–15,7 N • m
|
| 4. Connect two tubes of brake system. |
| 5. Tighten nuts of fastening of tubes of brake system. Inhaling moment: 1,8–21,6 N • m
|
| 6. Connect the socket to the sensor of level of brake liquid. |
| 7. Add brake liquid and remove air from a hydraulic contour of brake system. |
| 8. Connect a wire to the negative plug of the storage battery. |
|
|
|