Kia Clarus/Credos

1995-2001 of release

Repair and car operation



KIA Klarus
1.1. Periodicity of maintenance
+ 2. FE DOHC engines and Т8 DOHC
+ 3. Greasing system
+ 4. Cooling system
+ 5. Power supply system and release
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. Mechanical transmission
- 10. АКП G4A–EL
   10.1. Specifications
   10.2. Search and determination of malfunctions
   10.3. Table of fast diagnostics
   10.4. Self-diagnostics system
   10.5. Codes of malfunctions
   10.6. Diagnostic socket
   10.7. Postrepair operation
   10.8. Testing of collaboration of an automatic transmission and the engine on the motionless car
   10.9. Testing for delay time
   10.10. Testing of pressure of transmission liquid
   10.11. Testing for the pressure reduced by the valve
   10.12. Check of level and a liquid condition in an automatic transmission
   10.13. Leakages of liquid from an automatic transmission
   10.14. Cable of a drive of a butterfly valve
   10.15. Mode switch
   10.16. Switch of stoplights
   10.17. Sensor of temperature of transmission ATF liquid
   10.18. Check of resistance of the generator of impulses
   10.19. Electromagnetic valves
   10.20. Removal of an automatic transmission
   10.21. General recommendations about transmission dismantling
   10.22. Dismantling of an automatic transmission
   10.23. Check and adjustment of preliminary loading of bearings
   10.24. Assembly of an automatic transmission
   10.25. Installation of an automatic transmission
   10.26. Oil radiator
   10.27. Driving disk
   10.28. Check of work and adjustment of position of the lever of the selector
   10.29. Selector lever
   10.30. Repair of the lever of the selector
+ 11. АКП 50–40 LE
+ 12. Axes and power shafts
+ 13. Steering
+ 14. Wheels and tires
+ 15. Suspension bracket
+ 16. Body
+ 17. Central air
+ 18. Electric equipment
+ 19. Brake system
+ 20. Electric circuits






10.30. Repair of the lever of the selector

GENERAL INFORMATION

Selector lever

1–socket;
2–screws;
3–head of the lever of the selector;
4–casing;
5–display panel;
6–lamp of the indicator of situation;
7–cam;
8–roller clamp assembled;
9–auxiliary plate;
10-elastic plate, top;
11-elastic plate;
12-pin;
13-roller clamp;
14-axis;
15-nut;
16-selector lever;
17-a directing plate;
18-arm of the lever of the selector.

Dismantling, check and assembly

PERFORMANCE ORDER
1. Disassemble the selector lever in the sequence shown in drawing.
2. Insert a thin slice of metal from contacts of the socket and squeeze out down a pin for their fixing.
3. To Vytolknita contacts from the socket.
4. Check a condition of details and, if necessary, repair or replace them.
5. Assembly is carried out in sequence, return dismantling.
6. Put konsistentny greasing from the interior of a clamp and establish it on an elastic plate.
7. Move the selector lever to situation P.
8. Establish in a free condition an elastic plate, the top elastic plate and an auxiliary plate.
9. Adjust a gap between a directing plate and a directing pin and tighten screws.

Inhaling moment: 2,0–2,9 N • m

10. Establish in a free condition a cam on a pusher.


Prevention

The gap decreases at a cam povorachivaniye clockwise.


11. Adjust a gap between a directing plate and a directing pin a cam povorachivaniye.
12. Establish a head of the lever of the selector and make sure that the gap corresponds to the specified values.
13. Otherwise, repeat assembly, since a step 2.
14. Remove a head of the lever of the selector
15. Put konsistentny greasing on a cam, as is shown in drawing.
16. Move the selector lever to situation P.
17. Combine adjusting screws in the toddler with openings in the display panel. Establish a thick wire for support of the toddler.
18. Temporarily establish the display panel on an arm of the lever of the selector.
19. Tighten screws of the display panel in an order specified in drawing.

Inhaling moment: 2,0–2,9 N • m

20. Remove a wire.
21. Make sure that position of the lever of the selector corresponds to the display panel in each situation.